Soft Vertical Blinds Support
LIVE Chat Online
LIVE Chat Online
Extra carriers cannot be added to a vertical blind after manufacturing. If a replacement carrier is needed, please contact a retailer to purchase a new vertical blind headrail, or contact customer service for cost or warranty coverage information.
No, the tilt chain will only face one way. If the headrail is attached the wrong way, the tilt chain will face away from the room. To change headrail and tilt chain direction, first remove all vanes. Next, remove headrail and turn so controls are on the opposite side. Finish by reattaching vanes.
With a minor adjustment, you can create an overlap to eliminate the gap. First, mount the headrails with non-control ends touching. Then, look inside one of the headrails and remove one or more of the small whitish spacer tubes attached at the ends (Note: The spacer tubes are c-shaped and can be popped off with a screwdriver). This will allow the end vane to move closer to the edge of the rail allowing for overlap.
Occasionally the internal push nut is attached too tightly during production. To loosen, first remove the control end cap. You will see a pulley with a rod in the center. Locate the round metal washer with a ragged, star-shaped center on the rod. Tap the control rod lightly on the opposite end of the headrail to loosen the push nut and allow the controls to operate more smoothly. Finish by reattaching the control end caps. If the control chain is still difficult to operate, contact customer service for a return authorization number and repair cost or warranty coverage.
The standard way that soft vertical blind vanes are ordered is by length as measured from the top of the headrail to the bottom of the vane. Vertical vanes can also be ordered by actual vane length (without headrail) but this must be specified at the time the order is being placed.
Visit our cleaning and care page.
| Minimum Depth to Install | 2-7/8" |
| Flush Mount Headrail | 3-1/2" |
| Flush Mount Vanes and Fabric Folds (Pleats) | 6-1/4" |
| Flush Mount Channel Valance | 4-1/8" |
| Flush Mount Fabric Wrap Valance | 5-1/2" |
| Inside Mount | Outside Mount | |
|---|---|---|
| Headrail | 1/4" | 0" |
| Fabric | 1/4" | 0" |
| Blind Width | Number of Brackets | Number of Valance Clips |
|---|---|---|
| Up to 36" | 3 | 3 |
| 36-1/8" to 66" | 4 | 4 |
| 66-1/8" to 96" | 5 | 5 |
| 96-1/8" to 126" | 6 | 6 |
| 126-1/8" to 144" | 7 | 7 |
| One Way Minimum Width | Dual Stack Minimum Width | Center Stack Minimum Width | One Way, Dual, and Center Stack Maximum Width | Minimum Height | Maximum Height | |
|---|---|---|---|---|---|---|
| Inside Mount (IM) | 13-3/8" | 25-7/8"" | 48" | 144" | 12" | 144" |
| Outside Mount (OM) | 13-1/8" | 25-5/8"" | 48" | 144" | 12" | 144" |
| Blind Height | Cordless Wand Length |
|---|---|
| 18" - 24" | 12" |
| 24-1/8" - 36" | 20" |
| 36-1/8" - 96" | 33" |
| 96-1/8" - 108" | 47" |
| 108-1/8" - 120" | 59" |
| 120-1/8" - 132" | 69" |
| 132-1/8" - 144" | 80" |
Length of cordless wand is from top of headrail
| Blind Height | Cord Length |
|---|---|
| Less than 19" | 12" |
| 19-1/8" - 96" | 7" less than total length |
| Over 96" | 90" |
Tilt chain is standard 42" unless otherwise specified
These charts represent the amount of shade that is gathered to either side of the window when fully drawn. The measurements in these charts include the stack of the fabric.
| One Way Stack | Dual Stack | |||||
|---|---|---|---|---|---|---|
| Blind Width | No. of Vanes | Stack Width | Clear Opening | No. of Vanes | Stack Width | Clear Opening |
| 13-1/8" | 4 | 3-7/8" | 9-1/4" | -- | -- | -- |
| 16-1/4" | 5 | 4-1/8" | 12-1/8" | -- | -- | -- |
| 19-3/8" | 6 | 4-1/2" | 15" | -- | -- | -- |
| 22-1/2" | 7 | 4-3/4" | 17-3/4" | -- | -- | -- |
| 25-5/8" | 8 | 5-1/8" | 20-1/2" | 8 | 3-7/8" | 18" |
| 28-3/4" | 9 | 5-1/2" | 23-1/4" | -- | -- | -- |
| 31-7/8" | 10 | 5-3/4" | 26" | 10 | 4-1/8" | 23-5/8" |
| 35" | 11 | 6-1/8" | 28-7/8" | -- | -- | -- |
| 38-1/8" | 12 | 6-1/2" | 31-5/8" | 12 | 4-1/2" | 29" |
| 41-1/4" | 13 | 6-3/4" | 34-1/2" | -- | -- | -- |
| 44-3/8" | 14 | 7-1/8" | 37-1/4" | 14 | 4-3/4" | 34-3/4" |
| 47-1/2" | 15 | 7-1/2" | 40" | -- | -- | -- |
| 50-5/8" | 16 | 7-3/4" | 42-3/4" | 16 | 5-1/4" | 40-3/8" |
| 53-3/4" | 17 | 8-1/8" | 45-5/8" | -- | -- | -- |
| 56-7/8" | 18 | 8-1/2" | 48-3/8" | 18 | 5-1/2" | 46" |
| 60" | 19 | 8-3/4" | 51-1/4" | -- | -- | -- |
| 63-1/8" | 20 | 9-1/8" | 54" | 20 | 5-3/4" | 51-1/2" |
| 66-1/4" | 21 | 9-3/8" | 56-7/8" | -- | -- | -- |
| 69-3/8" | 22 | 9-3/4" | 59-5/8" | 22 | 6-1/8" | 57" |
| 72-1/2" | 23 | 10-1/8" | 62-3/8" | -- | -- | -- |
| 75-5/8" | 24 | 10-3/8" | 65-1/4" | 24 | 6-1/2" | 62-3/4" |
| 78-3/4" | 25 | 10-3/4" | 68" | -- | -- | -- |
| 81-7/8" | 26 | 11-1/8" | 70-3/4" | 26 | 6-3/4" | 68-1/4" |
| 85" | 27 | 11-3/8" | 73-1/2" | -- | -- | -- |
| 88-1/8" | 28 | 11-3/4" | 76-3/8" | 28 | 7-1/8" | 74" |
| 91-1/4" | 29 | 12-1/8" | 79-1/8" | -- | -- | -- |
| 94-3/8" | 30 | 12-3/8" | 82" | 30 | 7-1/2" | 79-1/2" |
| 97-1/2" | 31 | 12-3/4" | 84-3/4" | -- | -- | -- |
| 100-5/8" | 32 | 13" | 87-5/8" | 32 | 7-3/4" | 85-1/8" |
| 103-3/4" | 33 | 13-3/8" | 90-1/4" | -- | -- | -- |
| 106-7/8" | 34 | 13-3/4" | 93" | 34 | 8" | 90-5/8" |
| 110" | 35 | 14" | 96" | -- | -- | -- |
| 113-1/8" | 36 | 14-3/8" | 98-3/4" | 36 | 8-1/2" | 96-1/4" |
| 116-1/4" | 37 | 14-3/4" | 101-1/2" | -- | -- | -- |
| 119-3/8" | 38 | 15" | 104-3/8" | 38 | 8-3/4" | 101-7/8" |
| 122-1/2" | 39 | 15-3/8" | 107-1/8" | -- | -- | -- |
| 125-5/8" | 40 | 15-3/4" | 110" | 40 | 9-1/8" | 107-3/8" |
| 128-3/4" | 41 | 16" | 112-3/4" | -- | -- | -- |
| 131-7/8" | 42 | 16-3/8" | 115-1/2" | 42 | 9-3/8" | 113" |
| 135" | 43 | 16-3/4" | 118-1/2" | -- | -- | -- |
| 138-1/8" | 44 | 17" | 121" | 44 | 9-3/4" | 118-5/8" |
| 141-1/4" | 45 | 17-3/8" | 123-7/8" | -- | -- | -- |
| 144" | 46 | 17-5/8" | 126-1/2" | 46 | 10" | 124-1/4" |