Vertical Blinds

Measuring For Inside Mount Vertical Blinds

Find Width:

Measure the opening across the top where the headrail is to be installed from inside of window frame on left to inside of window frame on right. Round the measurement down to the nearest 1/8". A minimum depth of 2-7/8" is needed to install inside the window.

Find Height:

Measure from the inside top of the opening on the left, at the center, and on the right to the sill; to the closest 1/8" and note the smallest dimension.

Do not make any allowances: adjustments will automatically be made so the headrail will fit the opening properly and the vanes will clear the sill by 1/4" to 1/2".

Measuring For Outside Mount Vertical Blinds

Find Width:

Measure the width of the area to be covered at the place where the headrail will be installed to the nearest 1/8". Blind should overlap opening at least 4" on each side to ensure privacy. To maintain the maximum view, allow adequate overlap and consider the stack width.

Find Height:

Measure the height of the area to be covered round down to the nearest 1/8". Blind should extend at least 3" above and 3" below opening or window moulding.

For installations to the floor, deduct 1/2" from the shortest height for proper clearance.

Specifying outside mount measurement means the factory makes allowances for headrail deductions only.

Measuring For Patio Doors

Find Width:

Measure the width of the area to be covered at the place where the headrail will be installed to the nearest 1/8". Blind should overlap opening at least 4" on each side to ensure privacy.

Find Height:

Measure the height of the area to be covered at the left, center and right and round down to the nearest 1/8". Blind should extend at least 3" above opening or window moulding.

To ensure easy access through the door and allow adequate overlap, consider the stack width.

For installations to the floor, deduct 1/2" from the shortest height for proper clearance.

Specifying outside mount measurement means the factory makes allowances for headrail deductions only.

Before you begin your installation:

Read all installation instructions!

• Make sure that you have all tools and hardware needed for installation.
• Check the installation surface (wall, ceiling, or window frame) to ensure that you have suitable fasteners and tools for the material.
• Double check the headrail and blinds for proper width and length. If you are installing several sets of blinds, be sure to match them with the appropriate window.
• Check the parts list shipped with the product to confirm that you have the correct number of brackets.

Tools You May Need (not included):

• Tape Measure
• Level
• Pencil
• 3/8" Wrench
• Flat-blade or Philips Head Screwdriver
• 1/4" Nutdriver
• Drill with Bits
• Drywall Anchors
• Safety glasses
• Scissors or Utility Knife
• Ladder

Optional Brackets:

Extension Brackets

(Offers clearance for obstructions) Outside-mounting extension brackets will provide 1"–3" clearance between the headrail and mounting surface. Assemble extension bracket as shown.

 

Step 1

Mounting Brackets

Outside Mount Bracket

Inside Mount Bracket

Headrail with vane carrier

Step 1A

Mark the bracket locations - outside-mount installation

• Position one bracket at each end of the headrail, 3" in from the ends.
• Space any remaining brackets evenly, not more than 30" apart.
• Mark the bracket mounting hole locations at the desired height, making sure they are level and square. Allow at least 1/2" clearance for vanes above the floor or sill.

Step 2A

Install the brackets - outside-mount installation

• If mounting into drywall or plaster, use 3/16" drill bit and insert wall anchors before inserting screws.

Step 1B

Mark the bracket locations— inside-mount installation

• Position one bracket at each end of the headrail, 3" in from the ends.
• Space any remaining brackets evenly, not more than 30" apart.
• Mark the bracket locations, making sure they are in a straight line that is parallel to the wall.

Determining the correct distance from the wall or window:

• Position the center of the brackets a minimum of 2-1/2" in front of the window frame or any protruding trim or handles.

Step 2B

Install the brackets— inside-mount installation

• Install in a wood window frame using the included screws.

For models equipped with a valance, the valance mounting clips should be installed to the headrail at this time. Please refer to the installation instructions included with your valance before proceeding

Step 3

Attach the headrail — outside- or inside-mount

• NOTE: For wide windows and sliding glass doors, two people are recommended for installing the headrail.
• With the bracket positioned as shown, fit the top front lip of the headrail into the front part of the spring clip.
• Tip the back of the headrail up into the spring clip until it locks with a clicking sound.

Step 4

Center the Vane Rotation

Models With Wand

• Attach the wand.
• Rotate the wand so that the vane clips are at a right angle to the window.

Models with Vane-Rotation Chains

• Adjust the vane-rotation chain so that it is centered (ends of chain should be even). Vane clips should be at a right angle to the window (open position).

Step 5

Attach the vanes

• Starting at one end, align the rectangular hole in the vane with the clip.
• Slide the vane fully into the clip; then pull down slightly to lock the hook on the clip into place. Repeat for the remaining vanes, making sure that all vanes are facing in the same direction.

• Left Image - Vanes nest correctly for optimum light control.
• Right Image - Vanes nest incorrectly, preventing optimum light control.

• Bottom Chains (if ordered)
• Connect the vanes together with the included clips and chain.

Step 6

Attach the tension device (cord/chain control only)

Refer to instructions in the hold-down tension device.

Step 7

Test the Vane Rotation

Turn the wand or pull the bead chain in alternate directions to ensure that the vanes rotate smoothly in both directions.

Step 8

Test the Traverse

With the vanes in the open position (vanes at a right angle to the window), slide the wand or pull the cord in alternate directions to ensure that the vanes move smoothly in both directions.

Please refer to the valance instructions for your valance style at this time to complete your installation.

Dimensions and Installations Depth Requirements

Number of Installation Brackets and Valance Clips

Factory Deductions

Size Limitations

Control Length

Length of cordless wand is from top of headrail

Tilt chain is standard 42" unless otherwise specified

Specialty Shapes

Angle Top

Give the following dimensions: Straight Width, Angle Width, Right Height, Left Height, Mounting Style: Inside or Outside, Control Side: Right or Left

NOTE: Not all angle top headrails traverse. Check with customer service at time of order.

Cutout

Measure the following:

1. The overall width of the blind
2. The right height of the blind
3. The left height of the blind
4. The width of the obstacle

NOTE: Allow 1/4" clearance for the obstacle. The overall width of the obstacle plus the obstacle offset must equal the overall width. Maximum of two cutouts per blind.

FOR TEMPLATES

Please make a paper template in an acceptable material, cut the template out to shape and write the purchase order number, customer’s name, width and height on the FRONT of the template that faces inside room (sizes must be to the nearest eighth of an inch).

Please mail template to:
LEVOLOR Template Dept
4310 Regency Drive Suite 101
High Point NC 27265

Be sure to indicate your name, store name, and purchase order number on the template.

FOR DIAGRAMS

Please make a drawing/diagram & write the purchase order number, customer name and the measurement of every side/angle (including the top angle side).

Please fax diagram to:
Attn LEVOLOR Diagram
336-781-1211

Sizes must be to the nearest eighth of an inch. Do not mail a paper diagram. It will be returned as unacceptable.

TEMPLATES ARE REQUIRED FOR - FULL ARCH, HALF-ARCHES, CATHEDRAL ARCHES, CIRCLE/OCTAGON
DIAGRAMS ARE REQUIRED FOR - FANNED ANGLES, CUTOUTS