*Pecan and Walnut also available in Vertical Vanes.
LEVOLOR stock blinds and shades can be custom cut in store by an associate, so you can get a better fit, light control and privacy.
Plantation Faux Wood Blinds offer all the beauty of real wood at a fraction of the cost. Durable, warp resistant slats make this product a great choice for any room, especially spaces with high humidity or a lot of routine wear and tear. LEVOLOR'S exclusive room-darkening LightMaster™ feature increases privacy and light control. Coordinating colors and finishes are now available in Vertical blinds to help you create the perfect look.
No-holes design increases privacy and light control.
Headrails are constructed out of durable, long lasting aluminum instead of plastic.
Cord tilt provides tighter closure and increased privacy.
Measure exact distance to the nearest 1/8" between inside surfaces of window frame at the top, middle, and bottom, and use the narrowest width. Do not make any width deductions. Factory will make the appropriate deductions.
Measure exact distance to the nearest 1/8" from inside surface at top of window to sill at the left, middle and right and use the longest height. If you prefer blind not to touch sill, deduct 1/4". If there is no sill, measure height to point where blind is to reach.
|Standard Factory Adjustments From Ordered Width|
Measure exact distance to the nearest 1/8" between the outermost points where the blind is to be placed. For optimum light control, this measurement should extend 3/4" beyond the window opening on each side (or 1-1/2" for the entire width).
Measure exact distance to the nearest 1/8" from where top of blind will be located to top of sill. If there is no sill or if blind is to overlap window frame, measure to point blind is to reach.
|Allow Some Overlap|
For outside mount applications allow the blind to overlap 1-1/2" to 3" on the sides, top and bottom of the window.
You must add the overlap to your measurement; LEVOLOR does not add width or height for overlap on Outside Mounted blinds.
|Standard Factory Adjustments From Ordered Width|
|Blind Width||No adjustment||No adjustment|
|Valance||1" added||No adjustment|
NOTE: Whether you have a protruding or flush mount application is entirely dependent on the available depth of your window.
(Height x Depth)
(Side, Back or Top Mount)
Headrail Flush Mount
Valance Flush Mount
|1" Slat Size||1" x 1-1/2"||1/2"||1-3/4"||2-5/8"|
|2" Slat Size||1-1/2" x 2-1/4"||3/4"||2-1/2"||3-1/2"|
|2-1/2" Slat Size||1-1/2" x 2-1/4"||1-1/4"||3"||3-1/2"|
|Width||Up to 37 in.||37 in. to 47 in.||Greater than 47 in.|
|A. Box Bracket (Left and Right)||2||2||2|
|B. Support Bracket||0||1||1|
|C. Valance Clip||2||2||3|
|D. Bottomrail Endcap*||2||2||2|
|E. Hold-down Bracket**||2||2||2|
|F. #5 Screw x 3/4 in.**||4||4||4|
|G. #6 Screw x 1 1/4 in.||5||7||7|
*Not Required for Real Wood. **Not required for Real Wood or Cordless Faux Wood
Remove these parts packed in the headrail. Quantity varies with blind size.
Left Bracket / Right Bracket
Snap together where applicable.
IF APPLICABLE: Hold-down Brackets
The following are instructions to shorten LEVOLOR Stock corded wood blinds.
Install and lower the blind fully.
Select the slat that is even with the window sill or slightly below it.
Count 2 slats below the slat that is even with your window sill and cut both ladder cords directly below the slat (repeat for all sets of ladders).
NOTE: The ladder cord is the braided cord; be careful not to cut any other cords.
Cut both lift cords approximately 6 in. below the new bottom slat (repeat for all sets of lift cords).
Remove the bottom two slats.
Pry all plugs from the bottom rail.
Use tweezers or needle nose pliers to remove all knotted ends of the lift cord from the bottom rail slots.
Insert the bottom rail through all the ladder cords below your new bottom slat.
Pull the lift cord out of the last loop on the ladder cord below the bottom rail (repeat for all lift cords).
Insert the lift cord into the front (or back) side of the bottom rail (repeat for all lift cords).
Pull the lift cords through the bottom hole (repeat for all lift cords).
Tie each pair of lift cords together and add an extra knot for security.
Trim the excess lift and ladder cords (repeat for all lift and ladder cords).
Stuff any remaining ladder cords into the bottomrail and reinsert the plugs seating the cords in the plug notches (repeat for all ladder cords).
LEVOLOR® is proud to extend a limited lifetime warranty (with life of product defined as 5 years) on the enclosed product.
Warranty covers the original purchaser in the case of manufacturing defects (i.e. a flaw in the product design, materials, or workmanship) providing the product has remained in its original window.
Normal wear and tear
Any product that fails due to:
Any product that, with the passage of time, exhibits:
Natural material (including, but not limited to wood, grass, jute, reeds) products that have:
Costs associated with:
In the event there are multiple blinds/shades in the same room, only the defective blind/shade will be replaced.
For online product-specific trouble shooting information, refer to www.LEVOLOR.com. If you suspect this LEVOLOR® product has a manufacturing defect in materials or workmanship:
Any unauthorized returns will not be accepted.
If this LEVOLOR® product is found to have a manufacturing defect in materials or workmanship, we will (at our discretion) do one of the following:
Colors vary from lot to lot and may not exactly match sample swatch or previous purchases
Discontinued items or color selections will be replaced with the closest equivalent current product
This limited warranty gives you specific legal rights and you may have other rights, which vary from state to state.
Some states do not allow limitations on how long a warranty lasts, so the above limitations may not apply to you. No agent representative, dealer or unauthorized employee has the authority to increase or alter the obligation of this warranty. This limited warranty supersedes any previous versions.